Effectiveness Analysis of Hydraulic Torque Wrench Machine Using Failure Mode and Effect Analysis (FMEA) and Logic Tree Analysis Study Case on Heavy Equipment Manufacturing
DOI:
https://doi.org/10.37385/jaets.v5i1.1920Keywords:
Process Capability, Overall Equipment Effectiveness, FMEA, Manufacturing, Production EngineeringAbstract
Production quality in terms of process efficiency and quality in the manufacturing industry must always be improved in order to maintain customer confidence. PT XYZ as a heavy equipment assembly company is one of the companies that depends on process reliability for a smooth production process. Based on this, the problems raised in this study focus on increasing the efficiency of the process of installing bolts on slew bearings. By using Overall Equipment Efficiency (OEE) and Process Capability (CpK) as the main benchmarks for measuring the quality of the production process where the latest data shows the average OEE value is at 18.53%, while the CpK value for the bolt tightening process is at 0 ,67. The OEE and CpK figures obtained show that the process quality is still not optimal and needs to be improved. The purpose of this research is to identify and prevent as many factors as possible that can lead to process failure. The methods used to evaluate processes and to identify where and how a process might fail are Failure Mode and Effect Analysis (FMEA) and Logic Tree Analysis (LTA). Both methods are used to identify and prevent as many factors as possible that can lead to a process failure. The results of research using the FMEA and LTA methods show that in the process of installing slew bearing bolts there is a process that needs to be improved because the RPN value is quite high, namely above 125. Some suggestions for improvement such as the use of a manipulator arm on a torque tool and the implementation of a manufacturing execution system (MES) can reduce the RPN value from above 125 to 28, where the process obtained is better than before.
Downloads
References
Ahn, J., Noh, Y., Park, S. H., Choi, B. I., & Chang, D. (2017). Fuzzy-based failure mode and effect analysis (FMEA) of a hybrid molten carbonate fuel cell (MCFC) and gas turbine system for marine propulsion. Journal of Power Sources, 364, 226–233. https://doi.org/10.1016/j.jpowsour.2017.08.028
Altuntas, S., & Kansu, S. (2019). An innovative and integrated approach based on SERVQUAL, QFD and FMEA for Service Quality Improvement. Kybernetes, 49(10), 2419–2453. https://doi.org/10.1108/k-04-2019-0269
Antoniolli, I., Guariente, P., Pereira, T., Ferreira, L. P., & Silva, F. J. G. (2017). Standardization and optimization of an automotive components production line. Procedia Manufacturing, 13, 1120–1127. https://doi.org/10.1016/j.promfg.2017.09.173
Atmaja, L. T., Supriyadi, E., & Utaminingsih, S. (2018). Analisis efektivitas mesin pressing PH-1400 dengan metode overall equipment effectiveness (OEE) di PT. Surya Siam Keramik. Teknologi?: Jurnal Ilmiah Dan Teknologi, 1(1), 35. https://doi.org/10.32493/teknologi.v1i1.1415
Baghery, M., Yousefi, S., & Rezaee, M. J. (2016). Risk measurement and prioritization of auto parts manufacturing processes based on process failure analysis, interval data envelopment analysis and Grey Relational Analysis. Journal of Intelligent Manufacturing, 29(8), 1803–1825. https://doi.org/10.1007/s10845-016-1214-1
Carlson, C. S. (2012). Effective FMEAS: Achieving safe, reliable, and economical products and processes using failure mode and effects analysis. Wiley.
Chen, X., & Voigt, T. (2020). Implementation of the manufacturing execution system in the food and beverage industry. Journal of Food Engineering, 278, 109932. https://doi.org/10.1016/j.jfoodeng.2020.109932
Dobra, P. & Jósvai, J. (2021). Correlation between Overall Equipment Effectiveness (OEE) and Failure Mode and Effect Analysis (FMEA) at the semi-automatic assembly lines. In Proceedings of the IAC, Budapest, Hungary, 26–27 November 2021.
Glass, R., Seifermann, S., & Metternich, J. (2016). The spread of Lean production in the Assembly, process and machining industry. Procedia CIRP, 55, 278–283. https://doi.org/10.1016/j.procir.2016.08.021
Kemenperin: Sektor Manufaktur Tumbuh Agresif di Tengah Tekanan Pandemi. Kementerian Perindustrian. (n.d.). https://kemenperin.go.id/artikel/22681/Sektor-Manufaktur-Tumbuh-Agresif-di-Tengah-Tekanan-Pandemi-
Lam, N. T., Toi, L. M., Tuyen, V. T., & Hien, D. N. (2016). Lean line balancing for an electronics assembly line. Procedia CIRP, 40, 437–442. https://doi.org/10.1016/j.procir.2016.01.089
Liu, H.-C., You, X.-Y., Tsung, F., & Ji, P. (2018). An improved approach for failure mode and effect analysis involving large group of experts: An application to the Healthcare Field. Quality Engineering, 30(4), 762–775. https://doi.org/10.1080/08982112.2018.1448089
Lo, H.-W., Liou, J. J. H., Huang, C.-N., & Chuang, Y.-C. (2019). A novel failure mode and effect analysis model for Machine Tool Risk Analysis. Reliability Engineering & System Safety, 183, 173–183. https://doi.org/10.1016/j.ress.2018.11.018
Mantravadi, S., & Møller, C. (2019). An overview of next-generation Manufacturing Execution Systems: How important is MES for industry 4.0? Procedia Manufacturing, 30, 588–595. https://doi.org/10.1016/j.promfg.2019.02.083
Miao, R., Shen, R., Zhang, S., & Xue, S. (2020). A review of bolt tightening force measurement and loosening detection. Sensors, 20(11), 3165. https://doi.org/10.3390/s20113165
Mutlu, N. G., & Altuntas, S. (2019). Risk analysis for occupational safety and health in the textile industry: Integration of FMEA, FTA, and Bifpet Methods. International Journal of Industrial Ergonomics, 72, 222–240. https://doi.org/10.1016/j.ergon.2019.05.013
Nagane, S. G. (2002). Simulation Study of Selectivity Bank in automotive industry (thesis). University of Kentucky Libraries, Lexington, KY.
Nakajima, S. (1990). Introduction to TPM - total productive maintenance. Productivity Pr.
Nguyen, M.-N., & Do, N.-H. (2016). Re-engineering assembly line with Lean Techniques. Procedia CIRP, 40, 590–595. https://doi.org/10.1016/j.procir.2016.01.139
Perico, P., Arica, E., Powell, D. J., & Gaiardelli, P. (2019). Mes as an enabler of Lean Manufacturing. IFAC-PapersOnLine, 52(13), 48–53. https://doi.org/10.1016/j.ifacol.2019.11.306
Rachieru, N., Belu, N., & Anghel, D. C. (2013). Improvement of process failure mode and effects analysis using fuzzy logic. Applied Mechanics and Materials, 371, 822–826. https://doi.org/10.4028/www.scientific.net/amm.371.822
Rusman, M., Parenreng, S. M., Setiawan, I., Asmal, S., & Wahid, I. (2019). The overall equipment effectiveness (OEE) analysis in minimizing the six big losses: An effort to green manufacturing in a wood processing company. IOP Conference Series: Earth and Environmental Science, 343(1), 012010. https://doi.org/10.1088/1755-1315/343/1/012010
Sakthivel, G., & Ikua, B. W. (2017). Failure mode and effect analysis using fuzzy analytic hierarchy process and GRA topsis in manufacturing industry. International Journal of Productivity and Quality Management, 22(4), 466. https://doi.org/10.1504/ijpqm.2017.087864
Shivakumar, K. M., Hanumantharaya, R., Mahadev, U. M., & Kiran, P. A. (2015). Implementation of FMEA in injection moulding process. International Journal of Engineering Trends and Technology, 22(5), 230–235. https://doi.org/10.14445/22315381/ijett-v22p249
Su, X., Deng, Y., Mahadevan, S., & Bao, Q. (2012). An improved method for risk evaluation in failure modes and effects analysis of aircraft engine rotor blades. Engineering Failure Analysis, 26, 164–174. https://doi.org/10.1016/j.engfailanal.2012.07.009
Tripathi, S., & Jain, S. (2017). Study of the product failure modes and effects analysis (PFMEA) on welding process- an implementation paper. International journal of innovative research in science, engineering and technology, 6(5), 7991-7996. http://www.ijirset.com/upload/2017/may/91_Study.pdf
Wang, L., Hu, Y. P., Liu, H. C., & Shi, H. (2019). A linguistic risk prioritization approach for failure mode and effects analysis: A case study of medical product development. Quality and Reliability Engineering International, 35(6), 1735–1752. https://doi.org/10.1002/qre.2472
Wang, Z., Gao, J.-M., Wang, R.-X., Chen, K., Gao, Z.-Y., & Jiang, Y. (2018). Failure mode and effects analysis using Dempster-Shafer Theory and topsis method: Application to the gas insulated metal enclosed transmission line (gil). Applied Soft Computing, 70, 633–647. https://doi.org/10.1016/j.asoc.2018.06.015
Wessiani, N. A., & Yoshio, F. (2018). Failure mode effect analysis and fault tree analysis as a combined methodology in risk management. IOP Conference Series: Materials Science and Engineering, 337, 012033. https://doi.org/10.1088/1757-899x/337/1/012033
Winatie, A., Maharani, B. P., & Rimawan, E. (2018). Productivity Analysis to Increase Overall Equipment Effectiveness (OEE) by Implementing Total Productive Maintenance. International Journal of Innovative Science and Research Technology, 3(12), 7. https://ijisrt.com/wp-content/uploads/2019/01/IJISRT18DC196.pdf